HappyModel Mobula6 2024 BNF ExpressLRS V2

Description Note: The only difference for v2 is it comes with V2.0 AIO FC with motor plug for convenience in replacing motors (V1.0 AIO FC is soldered motors) The HappyModel Mobula6 2024 BNF ExpressLRS delivers unparalleled FPV adventures. Experience ultra-light agility and cutting-edge features for unmatched aerial excitement. Features: AIO Flight controller with Serial ELRS Receiver and 5.8G Openvtx Super light 1S 65mm Brushless whoop only 17.7g Equipment with the lightest brushless motors-SE0702 only 1.46gram FX17-B 1/3 CMOS 800TVL Camera awesome footage Smooth and powerful Compatible for 1S Lipo/LIHV Specifications: Wheelbase: 65mm Size: 81mm*81mm*37mm Weight: 17.7g Includes: 1x Mobula6 2024 1S 65mm whoop Drone Frame   Canopy 1x SuperX ELRS AIO 5-IN-1 Flight controller 4x SE0702 KV28000 brushless motor 1x Gemfan 1208-3 31mm tri-blade propellers(4cw 4ccw) 1x FX17-B 1/3 CMOS 800TVL camera NTSC 4:3 1x Onboard 5.8G 25mw~400mw VTX 1x Spare canopy 1x Propeller disassemble tool 1x Screw driver Parts Specifications: Motor Mode: SE0702 KV28000 Configu-ration: 9N12P Stator Diamter: 7mm Stator Length: 2mm Shaft Diameter: Φ1mm Motor Dimension(Dia.*Len): Φ9.5mm*14mm Weight(g): 1.46g No.of Cells(Lipo): 1S only Propellers Materials: PC Inch: 31mm Pitch: 0.8 in Weight: 0.21g Mount hole diameter:  1mm Flight controller SuperX ELRS AIO 5-IN-1 Flight controller MCU:STM32F411CEU6 (100MHZ, 512K FLASH) ,ESP32-PICO-D4 Sensor:BMI270(SPI connection) Mount hole size: 25.5mm*25.5mm Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Built-in Betaflight OSD(SPI Control) Built-in 5.8G OpenVTX 0mw~400mw (MSP control) Built-in UART ExpressLRS v3.0.0 Built-in voltage meter sensor , voltage meter scale 110 Built-in current meter sensor , current meter scale 1175 Onboard 4in1 ESC Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: Bluejay v0.19.2 Default protocol: DSHOT300 Recommend ESC Startup power value to min1100/max1200 Onboard Serial ExpressLRS receiver Packet Rate option: 50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version: V3.0 RF Frequency: 2.4GHz Antenna: Enameled copper wire antenna Telemetry output Power: <12dBm Receiver protocol: Serial_based CRSF Compatible with ExpressLRS V3.x.x TX Module Could flash single ELRS receiver firmware by Wifi ExpressLRS firmware target: Generic ESP32 2.4Ghz Rx and VTx Onboard 5.8g VTX Firmware version: OPENVTX MSP VTX PIT Mode support Channels: 40ch Transmitting Power: 0/RCE/25mw/100mw/400mw Power supply: DC 5V Current (5v): <650ma (400mw) Antenna connector: U.FL FX17-B Camera Model: FX17-B Image Sensor: 1/3″ CMOS Horizontal Resolution: 800TVL FOV 150° Signal System: NTSC Net Weight: 1.5g Dimensions: L14mm*W14mm*H13mm Spare Parts (Not Included) Frame: HappyModel Mobula6 2024 Frame (Grey/Clear) Canopy: HappyModel Mobula6 2024 Camera mount bracket Motor: HappyModel SE0702 KV28000 for Mobula6 2024 Camera: HappyModel FX17-B FPV Nano Camera Charger: VIFLY WhoopStor V3 6 Ports 1S Storage Charger Discharger Props: TBC Recommended Batteries (Not Included): GNB Battery 3.8V 60C 300mAh 1S HV A30 Head Connector GNB Battery 3.8V 60C 380mAh 1S HV A30 Head Connector